Search Results (191)

This paper aims to guide structural engineers on how to apply the rapid nonlinear time history analysis (RNLTHA) procedure effectively to predict seismic demand, taking into account ductility and overstrength, and effects of dynamic phenomena including cyclic degradation of strength and stiffness in structures, in a direct and expedient manner. The shortcoming of the conventional force-based approach of design involving the use of a force reduction factor to account for nonlinear effects is well recognised. Nonlinear static (pushover) analysis and dynamic nonlinear time history analysis (NLTHA) are offered as alternative methods of analysis by major codes of practices to achieve better optimisation in the use of materials. NLTHA has advantages over pushover analysis in being more direct and capable of capturing cyclic response behaviour. Despite the merits of NLTHA, its adoption in the industry has been limited, mainly because of the complexity and the higher analysis cost involved. RNLTHA proposed in this article uses a macroscopic model of the building to fulfil the purpose of NLTHA, whilst saving computational time and achieving a good degree of accuracy, as verified by comparison with results generated from SeismoStruct. Full article

Fiber Reinforced Concrete (FRC) has shown significant promise in enhancing the safety and reliability of civil infrastructures. Structural Health Monitoring (SHM) has recently become essential due to the increasing demand for the safety and sustainability of civil infrastructures. Thus, SHM provides critical benefits for future research to develop more advanced monitoring systems that effectively detect and diagnose the damage in FRC structures. This study investigates the potential of an Electro-Mechanical Impedance (EMI) based SHM system for detecting cracks in FRC prisms subjected to four-point repeated loading. For the needs of this research, an experimental investigation of three FRC specimens with the dimensions 150 × 150 × 450 (mm) were subjected to three different loading levels where no visual cracks formed on their surface. Next, prisms were subjected to reloading until they depleted their load-carrying capacity, resulting in pure bending fracture at the mid-span. A network of nine cement paste coated Piezoelectric lead Zirconate Titanate (PZT) transducers have been epoxy bonded to the surface of the FRC prisms, and their frequency signal measurements were utilized for quantitative damage assessment. The observed changes in the frequency response of each PZT sensor are evaluated as solid indications of potential damage presence, and the increasing trend connotes the severity of the damage. The well-known conventional static metric of the Root Mean Square Deviation (RMSD) was successfully used to quantify and evaluate the cracking in FRC specimens while improving the efficiency and accuracy of damage detection. Similarly, the dynamic metric of a new statistical index called “moving Root Mean Square Deviation” (mRMSD) was satisfactorily used and compared to achieve and enhance accuracy in the damage evaluation process. Full article

This paper is aimed at serving the needs of structural engineering designers of an important structure (or a group of structures located on the same site) who is seeking guidance on how to obtain accelerograms and/or derive response spectra that accurately represent the site subsoil conditions as informed by the borelogs. The presented site-specific seismic action model may be used to replace the default seismic action model stipulated for the designated site class. Presented in this article is a procedure for generating soil surface motions in an earthquake, and their associated site-specific response spectra, taking into account details of the soil layers. Dynamic site response analyses are involved. The conditional mean spectrum methodology is employed for selecting and scaling accelerograms for obtaining input motion on bedrock. The selection depends on the natural period of both the site and the structure. Multiple borelogs taken from within the same site are analysed to identify the critical soil column models without having to conduct site response analysis on every borelog. The technique for simplifying the soil layers utilising the shear strain profile is introduced to further cut down on the time of analyses. The procedures described in this article have been written into a web-based program that is freely accessible to engineering practitioners. Full article

During the tender phase of public construction projects in Portugal, documents that describe the project are mandatorily submitted to open data repositories. However, in their current state, most of these repositories do not allow for benchmarking analysis due to a lack of data treatment and cohesion. This paper seeks to diagnose the main trends during the public construction project’s tender phase by performing a descriptive statistical analysis on the Portuguese Public Procurement Database (PPPData), a database that compiles 5172 public procurement contracts in Portugal from 2015 to 2022, to respond to the research gap in construction procurement benchmarking. The results of this statistical analysis draw out the main trends, uncover which tender variables can influence budget compliance, and diagnose Portugal’s public procurement in terms of its geographical, temporal, financial, and performance dispersion. This paper concludes that the award criteria are not correlated with final project performance and that multifactor assessment criteria do not necessarily lead to better performance. High-value projects awarded solely with the price award criterion tend to perform worse than those awarded with the multifactor assessment. The study also identified frequent errors and omissions in construction reporting; thus, there is a need for error mitigation tools. Full article

Current formulas to assess the shear capacity of headed steel stud anchors and post-installed (PI) anchors in case of pryout failure (sometimes known as pull-rear failure) have been derived either based on the indirect-tension resistance model or are fully empirical based on push-out test results. In both cases, the predicted pryout capacity is clearly conservative and underestimates the true pryout capacity of anchorages, especially for stiff anchors with low embedment-to-diameter ratios (h_ef/d < 4.5). This paper proposes an empirical and a semi-empirical formula to predict the concrete pryout capacity of headed steel studs and PI anchors. They were derived based on an improved indirect-tension model which accounts for the stud diameter and the stud spacing in a group of anchors. Furthermore, a database of 214 monotonic shear tests from the literature, including own tests (push-off and horizontally shear tests), is reevaluated and compared to the provisions of EN1992-4. The scope of this assessment proposal includes single and group of headed steel studs and PI anchors attached to a stiff steel plate as well as shear connectors in composite structures without metal deck embedded in normal-weight concrete. Full article

This paper presents the use of continuous wavelet transform (CWT) to capture the frequency contents, spectra of dominant frequencies and associated time durations of real earthquakes for generating artificial excitations to perform endurance time analysis (ETA) of structures. Applying CWT to three sets of forty earthquakes, the 90 percentile frequencies that span the ranges 0.08–18.41 Hz, 0.61–12.73 Hz, and 0.56–15.53 Hz; with associated time durations of 20, 15 and 16 s, respectively, for these earthquake sets are extracted. Artificial excitations that contain these ground motion characteristics are generated, progressively scaled up and applied to the target structure until failure. The scaling used is a block-shaped envelope that increases in size by a factor of 3/2 over time. Nonlinear seismic analyses of a steel frame and a concrete bridge bent using these artificial excitations have shown that the method not only successfully predicts the base shear–roof displacement responses of these structures, it also correctly identifies behavior such as weak story, concrete spalling, and core cracking. When compared with the increment dynamic analysis and time history analysis using multiple earthquakes, the proposed method is capable of producing comparable results with a significant reduction in computational time and a much smaller output file size. Full article

For massive monolithic foundation slabs, the problem of early cracking due to the intense heat release of concrete during the hardening process is relevant. The purpose of this article is to develop a simplified method for determining thermal stresses during the construction of massive monolithic foundation slabs. The proposed technique is based on the hypothesis of parabolic temperature distribution over the thickness of the structure at each moment of time. In addition to the parabolic distribution, the half-wave cosine distribution is also used. A hypothesis is also introduced about the same conditions of heat exchange with the environment on the lower and upper surfaces of the foundation. As a result, formulas are obtained that establish a direct relationship between thermal stresses and the temperature difference between the center and the surface. The solution to the test problem for the foundation slab is presented and compared with an alternative technique that does not use the hypothesis about the character of the temperature distribution over the thickness. Also, the inverse problem of determining the allowable temperature drop between the center and the surface of the structure is solved, at which the stresses on the upper surface at each moment of time will not exceed the tensile strength of concrete. Full article

The current paper presents the results of a study that analyzed and evaluated the efficiency of the largest container ports in the wider area of the Mediterranean Basin. The research question that this paper seeks to respond to is how the resources (inputs) of a container port reflect its level of activity and efficiency. In particular, what is the relationship between ports’ infrastructures, equipment and their productivity and the ports’ ability to attract economic activities as well as the extent of their effect on a port’s efficiency? The methodology uses the data envelopment analysis (DEA) output-oriented model following a cross-sectional approach. The research conducts two modeling approaches, the CCR and the BCC model. The analysis goes deeper and compares port efficiency estimates in relation to medium-sized and large ports’ classification and their total market share. The main findings indicated an average efficiency of 0.88 and 0.89 assuming constant and variable returns of scale, respectively, implying that the ports can increase their output levels up to approximately 1.2 times without any change in their inputs. Full article

Seismic isolation is a powerful tool for mitigating seismic risk and improving structural performance. However, some parameters, such as earthquake inputs and soil characteristics, influence the technology’s performance. This research aims to investigate the effects of soil–structure interaction (SSI) with regard to different moderate earthquakes associated with different distances of the source to the site, frequency content, and different soil characteristics on the seismic response of the isolated bridges. Near-fault (NF) and far-field (FF) records are applied to the conventional and isolated bridge with and without considering the underlying soil. For this reason, using the direct and simplified methods, three soil properties representing rock, dense, and stiff soils are modeled in Abaqus software. Nonlinear time history analysis (NLTHA) is carried out, and structural responses of both approaches in terms of maximum deck acceleration, base shear, and displacement of the deck and the isolation system are studied. Results demonstrate that the difference between the two approaches is significant. Using the simplified method is a rather simple approach that roughly captures the important features of the record characteristics and SSI. Furthermore, careful attention should be paid to the base shear responses and the isolator displacement demands, as they are significantly amplified in softer soils. In addition, the peak ground acceleration to peak ground velocity ratio (PGA/PGV) plays a decisive role in all dynamic responses. Records with a lower PGA/PGV ratio cause higher dynamic responses in terms of displacement and acceleration/force, regardless of the distance of the ruptured fault, while NF records show higher dynamic responses compared to FF records. Full article

Simplicity and optimality are commonly associated with the particle swarm optimization (PSO) algorithm. As a result, numerous variants and hybrids of PSO have been developed and implemented to address structural optimization problems. The undeniable importance of the initialization technique in determining the overall performance of a given optimization algorithm cannot be overstated. Optimization algorithms, such as PSO, typically rely on a random, uniformly distributed initialization. Through multiple iterations and updates, these algorithms aim to achieve optimal results. The underlying assumption behind such an initialization approach is that a fair or reasonable arrangement of particles is best accomplished through randomization, and thus the entire optimization process is iterated based on this assumption. However, this initialization technique raises concerns regarding the attainment of optimality and convergence, leaving room for further examination. In this paper, we challenge this assumption by introducing a priority concept. The key idea is that particles should not be initialized randomly since randomness alone does not guarantee a reasonable allocation of design variable values in iterative optimization. This can lead to misguided velocity updates and ultimately, a time-consuming pursuit of optimality. To address this issue, we formulate priority criteria (PC) and propose an enhanced PSO variant called Priority Criteria PSO (PCPSO). The PC can be incorporated into any PSO variant or hybrid without impacting the parameter settings, constraints, and penalty approaches of the respective algorithms. A case study involving 2D reinforced concrete frames was conducted to compare the performance of the ordinary PSO algorithm with the PCPSO. The results clearly demonstrate that the introduction of the PC leads to a significant cost reduction when compared to PSO with an inertia damping factor. Additionally, the PCPSO algorithm exhibits accelerated convergence. Furthermore, to alleviate the computational burden associated with structural analysis at each iteration, a reanalysis approach called Combined Approximations (CA) is mathematically formulated and implemented. Full article

This work presents a state-of-the-art review of existing fireproof construction guidelines for dwellings against wildfires. The most important wildfire-proof construction guidelines and codes for dwellings are presented, and these are later associated with existing fire engineering chapters associated with building codes. It was concluded that the variability in this subject is very high, and the approach to classifying the thermal effects in construction still lags behind scientific consensus. Moreover, the constructive requirements depend severally on the country’s building code when assessing the fireproof requirements for wildfire. Moreover, the thermal actions of wildfires in dwellings are presented and compared with classical ISO-834 standard fire curves, in which the maximum equivalent fire exposure time can range from 2 to 4 h depending on the country’s code. The key contributions of this work consist of (i) thoroughly disseminating codes and guidelines to promote scientific discussion in order to advance the wildfire fireproof standards dedicated to WUI; (ii) emphasizing the void in current codes in order to promote conversation between future researchers. Full article

Pakistan is currently facing physical and economic water scarcity issues, which have been further complicated by the rapid increase in its population and climate change. In affected areas, many methods are being used to tackle this problem, among which rainwater harvesting (RWH) provides the best alternative source of domestic water supply. In rainwater harvesting, a mechanism is designed to effectively collect surface runoff during rainfall events from residential rooftops. It has also been found that rainwater has great potential as a source of water supply in residential areas of major cities, such as Lahore, which is the focus of our study. This research paper examines rainwater harvesting as a sustainable solution to address the challenges of drinking water scarcity and urban flooding. The study discusses the benefits of rainwater harvesting, including reducing reliance on municipal water sources, improving water quality, and mitigating the impact of urban flooding. Additionally, the paper explores the use of filtered water points in conjunction with rainwater harvesting systems to provide clean drinking water to communities. The research draws on case studies from various regions to illustrate the effectiveness of rainwater harvesting as a sustainable solution to water scarcity and urban flooding. Ultimately, the study concludes that rainwater harvesting, when coupled with filtered water points, can offer an effective and sustainable solution to address drinking water scarcity and urban flooding. Full article

Structural pounding between adjoining multistory buildings with different total heights and different story levels has been repeatedly identified as a frequent cause of severe damage during seismic excitations. This phenomenon is very intense when upper floor slabs of short buildings hit the columns of taller and more flexible structures within their deformable length. On the other hand, it is well accepted that infill masonry panels strongly affect the seismic response and overall behavior of multistory reinforced concrete (RC) frames and especially in the common case of an open first story (pilotis). Thereupon, the interaction between a multistory frame with an open first floor and shorter and stiffer adjacent buildings was studied and the influence of the open first story on pounding investigated with inelastic dynamic step-by-step analyses. The results of the pounding cases of an 8-story RC frame with a single story and 4-story buildings were examined. Three cases of short structures were considered as follows: a frame structure, a stiff structure and a very stiff non-self-vibrating one. All studied interaction cases included type A (floor-to-floor) pounding cases and type B (floor-to-column) pounding cases. This study focused on the influence of an open first story (pilotis) on the pounding phenomenon. Therefore, all examined two-building poundings were studied considering two cases: the first case involving a fully infilled 8-story frame and second case involving an infilled 8-story structure with an open first story (pilotis). Moreover, as expected due to the asymmetry of the examined two-structured pounding pairs, the directions (plus and minus) of the seismic excitation proved to be important for the evaluation of the developing capacity demands. In the present study for the first time, it is stressed that pounding cases between structures with different geometries (asymmetric) have to be examined in both directions (plus and minus) of each seismic excitation. From the results, it can be deduced that the developing shear forces on the columns that suffer a hit in the case of type B pounding exceed the shear strength of the column even if detailing for critical regions according to Eurocode 8 is applied. Further, it is inferred that pilotis configuration increases the developing pounding forces and consequently increases the capacity demands mainly in terms of the ductility of the column that suffers the hit. Full article

Magneto-rheological dampers (MR-Dampers) are increasingly being used in construction applications to reduce the dynamic response of structures to seismic activities or severe wind loading. Sensors attached to the structure will signal the computer to supply the dampers with an electric charge that transfers the MR fluid to a near-solid material with different physical and mechanical properties (viscoelastic behavior). Control algorithms govern the fluid to near-solid conversion, which controls the behavior of the damper and the performance of the structure under the seismic or wind loading event. The successful optimization of control parameters minimizes the overall structural response to dynamic forces. The main objective of this research is to change the output behavior of specific floors within a building subjected to seismic excitation by optimizing the MR-Damper control parameters to impact the behavior of a specific floor or number of floors within the building. The adjustment of control parameters to attain this objective was validated in multiple case studies throughout this research. The successful implementation of the research outcome will result in optimized MR-damper design to meet the performance-based criteria of building projects. Full article

This paper presents a numerical study on the thermal effect of the insulation of lightweight concrete in hybrid GFRP-concrete structures. In these hybrid structures, the GFRP profiles are totally covered by normal and lightweight concrete and subjected to thermal loads. The problem with GFRP structures is their weak thermal resistance, even at moderately high temperatures. To promote some thermal insulation, it is recommended to cover the GFRP profile with concrete, but this increases its weight. Therefore, lightweight concrete may be a good solution due to its insulation capabilities. For this study, the thermal loads used in the numerical campaign are based on a nominal fire-curved ISO-834, and the temperature is measured at several points. Using these temperatures, it is possible to conclude that the effect of lightweight concrete may provide structural benefits when compared with classical standard structural concrete for covering GFRP profiles using different cover values (from 5.0 cm to 2.5 cm). For this work, commercial finite element software was used for the thermal nonlinear analysis. It was possible to conclude that with lightweight concrete, it is likely to have half of the cover and still maintain the same level of insulation as regular concrete. Full article