Journal Description
AgriEngineering
AgriEngineering
is an international, peer-reviewed, open access journal on the engineering science of agricultural and horticultural production, published quarterly online by MDPI.
- Open Access— free for readers, with article processing charges (APC) paid by authors or their institutions.
- High Visibility: indexed within Scopus, ESCI (Web of Science), PubAg, FSTA, AGRIS, CAPlus / SciFinder, and other databases.
- Journal Rank: CiteScore - Q1 (Horticulture)
- Rapid Publication: manuscripts are peer-reviewed and a first decision is provided to authors approximately 23.5 days after submission; acceptance to publication is undertaken in 4.7 days (median values for papers published in this journal in the first half of 2023).
- Recognition of Reviewers: reviewers who provide timely, thorough peer-review reports receive vouchers entitling them to a discount on the APC of their next publication in any MDPI journal, in appreciation of the work done.
Impact Factor:
2.8 (2022);
5-Year Impact Factor:
2.7 (2022)
Latest Articles
Sustainable Greenhouse Covering Materials with Nano- and Micro-Particle Additives for Enhanced Radiometric and Thermal Properties and Performance
AgriEngineering 2023, 5(3), 1347-1377; https://doi.org/10.3390/agriengineering5030085 - 04 Aug 2023
Abstract
►
Show Figures
This review aims to provide a comprehensive overview of nano- and microscopic materials that can provide thermal radiation insulation without reducing visible light transmittance, thereby reducing heat loss and conserving energy in greenhouses. We also reviewed the radial and thermal properties of greenhouse
[...] Read more.
This review aims to provide a comprehensive overview of nano- and microscopic materials that can provide thermal radiation insulation without reducing visible light transmittance, thereby reducing heat loss and conserving energy in greenhouses. We also reviewed the radial and thermal properties of greenhouse covering materials. Fillers, colorants, reinforcers, and additives, as well as glass, plastic film, and plastic sheet materials, were discussed. Additionally, by searching for keywords like insulation film, insulation agent, and infrared insulation, compounds based on graphene and fullerene as well as phase transition materials (PCMs) that may be used for radiation insulation, we proposed their potential use in greenhouse covers. They can be divided into semi-transparent photovoltaic (PV) materials, zinc oxide-based film fillers, and silica filter films. We discussed the radiation heat insulation and light transmission characteristics of these materials. Nano-synthesis techniques were also investigated. Based on latest advances in the literature, future developments in the micro- and macroscale synthesis of nanomaterials will enable additional innovations in covering materials for greenhouse structures. A limiting factor, though, was the high sensitivity of PVs to external climatic and meteorological variables. The ability of materials used to make greenhouse covers to control the microclimate, reduce CO2 emissions, use less energy, and increase agricultural productivity, however, cannot be disputed. Similar to this, a thorough examination of the uses of various greenhouse technologies reveals that the advancements also have financial advantages, particularly in terms of reducing greenhouse heating and cooling expenses. The PCMs, which decreased greenhouse-operating costs by maintaining constant ambient temperatures, provide ample evidence of this.
Full article
Open AccessArticle
Development and Performance Evaluation of Low-Cost 2WT-Operated Earthing-Up Machine for Sugarcane Cultivation in Bangladesh
by
, , , , , and
AgriEngineering 2023, 5(3), 1327-1346; https://doi.org/10.3390/agriengineering5030084 - 01 Aug 2023
Abstract
Like most crops, sugarcane needs to be kept upright until it is harvested. The lodging of sugarcane has significant negative effects on the cane yield and sugar content of sugarcane. To keep sugarcane upright, earthing up is an essential in the cultural part
[...] Read more.
Like most crops, sugarcane needs to be kept upright until it is harvested. The lodging of sugarcane has significant negative effects on the cane yield and sugar content of sugarcane. To keep sugarcane upright, earthing up is an essential in the cultural part of the operation. In Bangladesh, most of the sugarcane cultivation operations, including earthing-up, are generally performed in a traditional manual method which increases the production costs as well as reduces the income of sugarcane growers. Therefore, a cost-effective two-wheeled tractor (2WT)-mounted earthing-up machine was developed at the Bangladesh Sugarcrop Research Institute (BSRI), Pabna, to reduce drudgery and the cost of sugarcane production. Field tests were conducted in an experimental sugarcane field at BSRI and technical and economic performances of the developed earthing-up machine were also carried out based on the field test. The average effective field capacity and field efficiency of the earthing-up machine were found to be 0.16 ha/h and 77.41%, respectively. The 2WT-driven earthing-up machine was not found to be economically viable when it was used only for earthing-up operations. However, when the 2WT was used as the main driver for other activities, including earthing-up operation, the earthing-up machine became economically beneficial with net cash flow (NCF), net present value (NPV), internal rate of return (IRR), benefit–cost ratio (BCR), and payback period (PP) of BDT 148,497/ha, BDT 23,184, 3%, 3.81:1, and approximately 1 year, respectively. On the contrary, considering the cost of only earthing-up tool without 2WT, it was found to be economically beneficial with NCF, NPV, IRR, BCR, and PP of BDT 16,428/ha, BDT 3053, 4.7%, 2.71:1, and approximately 2 years, respectively. In Bangladesh, 2WT is commonly used for versatile farming purposes. Therefore, the versatile use of 2WT as a prime mover for other machines, including the earthing-up machine, can make earthing-up machine economically viable and beneficial for sugarcane growers in Bangladesh.
Full article
(This article belongs to the Section Agricultural Mechanization and Machinery)
►▼
Show Figures
Figure 1
Open AccessTechnical Note
Milking Machine Settings and Liner Design Are Important to Improve Milking Efficiency and Lactating Animal Welfare—Technical Note
AgriEngineering 2023, 5(3), 1314-1326; https://doi.org/10.3390/agriengineering5030083 - 28 Jul 2023
Abstract
The purpose of milking machines is to harvest milk at optimal quality and speed, while maintaining animal comfort and teat defense mechanisms against invading mastitis pathogens. Therefore, the milking machine is a very important piece of equipment on dairy farms to maintain a
[...] Read more.
The purpose of milking machines is to harvest milk at optimal quality and speed, while maintaining animal comfort and teat defense mechanisms against invading mastitis pathogens. Therefore, the milking machine is a very important piece of equipment on dairy farms to maintain a long healthy lactation by following the physiological conditions of the udder. The mechanical forces during long-term machine milking processes lead to changes in the teat tissue. This effect is related to the degree of adaptation of the milking machines to the physiological requirements of the individual udder anatomy and the physiological conditions of the lactating animals. If both, milking machine settings and liner design are not suitable for all teats and animals on the farm, some animals will not be fully milked, the teat condition will deteriorate over time and in the end, they may suffer from mastitis. Therefore, maintaining healthy udders and teats during milking is a central key component of an effective milking machine to produce good milk yield with higher quality by preventing mastitis and maintaining animal health and welfare. On large and thick teats, conventional liners often fit too tight, causing a massive mechanical stress load on the tissue. On small teats, however, they often do not adhere sufficiently close to the teat which can cause a considerable air admission and hence liner slips. The new liners, “Stimulor® StressLess” (Siliconform, Türkheim, Germany), have a wave-like lip construction and adapt well to the different teat sizes in a herd, thus ensuring consistent milking of lactating animals. A proper milking machine accommodates all teat sizes and forms, has a low vacuum to effectively open the teat and to stimulate physiological milk release and letdown. In addition, the right pulsation rate will maintain a stable vacuum on the teat area during milking. In conclusion, an ideal milking machine adapts to the morphological, anatomical, and physiological characteristics of the udder and teats of the lactating animals and it should achieve a physiologically ideal milking process that meets high animal welfare standards and increases milk production with a high quality standard.
Full article
(This article belongs to the Topic Emerging Agricultural Engineering Sciences, Technologies, and Applications)
►▼
Show Figures
Figure 1
Open AccessArticle
Spatial Variability of Soil Resistance to Penetration in Fruit Cultivation in Eastern Amazonia
by
, , , , , , and
AgriEngineering 2023, 5(3), 1302-1313; https://doi.org/10.3390/agriengineering5030082 - 21 Jul 2023
Abstract
The application of precision agriculture in cocoa and papaya cultivation in Brazil is still incipient. This study aimed to evaluate the spatial variability of the physical attributes of soil cultivated with a consortium of papaya and cocoa. The study was conducted in two
[...] Read more.
The application of precision agriculture in cocoa and papaya cultivation in Brazil is still incipient. This study aimed to evaluate the spatial variability of the physical attributes of soil cultivated with a consortium of papaya and cocoa. The study was conducted in two sampling grids of 50 points, in two areas cultivated with papaya and cocoa with different planting times (three and eleven months). The soil attributes soil resistance to penetration (RP) and soil gravimetric moisture (UG) were determined at soil depths of 0–20, 20–40 and 40–60 cm. The data were submitted to an exploratory and descriptive analysis. Subsequently, a geostatistical analysis was performed to quantify spatial dependence and then interpolation of the data through kriging. The maps showed weak spatial variability for the UG and RP. In the two areas, it was observed that the depth of 0–20 cm had a lower RP (1.7 Mpa) and a higher UG (40 g g−1), and as the depth was higher, had a higher RP (4.4 Mpa) and a lower UG (38 g g−1). Area 1 presented higher RP values in depth, showing greater susceptibility to compaction. The area characterized by the consortium of papaya and cocoa presented more susceptible to compaction. The mechanical resistance of the soil to penetration was more critical in the 40–60 cm layer for the two consortia evaluated, evidencing areas with possible restriction to plant growth.
Full article
(This article belongs to the Section Sensors Technology and Precision Agriculture)
►▼
Show Figures
Figure 1
Open AccessArticle
Integration of an Innovative Atmospheric Forecasting Simulator and Remote Sensing Data into a Geographical Information System in the Frame of Agriculture 4.0 Concept
by
, , , , and
AgriEngineering 2023, 5(3), 1280-1301; https://doi.org/10.3390/agriengineering5030081 - 17 Jul 2023
Abstract
In a world in continuous evolution and in which human needs grow exponentially according to the increasing world population, the advent of new technologies plays a fundamental role in all fields of industry, especially in agriculture. Optimizing times, automating machines, and guaranteeing product
[...] Read more.
In a world in continuous evolution and in which human needs grow exponentially according to the increasing world population, the advent of new technologies plays a fundamental role in all fields of industry, especially in agriculture. Optimizing times, automating machines, and guaranteeing product quality are key objectives in the field of Agriculture 4.0, which integrates various innovative technologies to meet the needs of producers and consumers while guaranteeing respect for the environment and the planet’s resources. In this context, our research aims to propose an integrated system using data coming from an innovative experimental atmospheric and forecasting simulator (capable of predicting some characteristic climate variables subsequently validated with local sensors), combined with indices deriving from Remote Sensing and UAV images (treated with the data fusion method), that can give fundamental information related to Agriculture 4.0 with particular reference to the subsequent phases of system automation. These data, in fact, can be collected in an open-source GIS capable of displaying areas that need irrigation and fertilization and, moreover, establishing the path of an automated drone for the monitoring of the crops and the route of a self-driving tractor for the irrigation of the areas of interest.
Full article
(This article belongs to the Special Issue Implementation of Artificial Intelligence in Agriculture)
►▼
Show Figures
Figure 1
Open AccessArticle
Comparative Analysis of Primary and Secondary Metabolites in the Peel of Eight Blood Orange Varieties
by
, , , , , and
AgriEngineering 2023, 5(3), 1259-1279; https://doi.org/10.3390/agriengineering5030080 - 14 Jul 2023
Abstract
The global cultivation of blood oranges is experiencing an increase due to their remarkable nutritional properties. Blood orange by-products, especially the peel, have a high concentration of bioactive compounds with exceptional antioxidant potential, making them an ideal choice for incorporation into various food
[...] Read more.
The global cultivation of blood oranges is experiencing an increase due to their remarkable nutritional properties. Blood orange by-products, especially the peel, have a high concentration of bioactive compounds with exceptional antioxidant potential, making them an ideal choice for incorporation into various food products. This study aimed to determine the morphological parameters and primary and secondary metabolite content of peel of eight blood orange varieties using 1H NMR and HPLC-ESI-DAD-MSn. “Tarocco Meli” had the highest weight (367.83 g), caliber (94.13 mm and 88.87 mm), peel thickness (6.73 mm), and peel weight (155.0 g). “Tarocco Rosso”, “Sanguinelli”, and “Tarocco Gallo” had the highest levels of total amino acids (25.57 g kg−1 DW), total organic acids (29.99 g kg−1 DW), and total sugars (68.56 g 100 g−1 DW), respectively. The peel of “Moro” had significantly higher concentrations of total anthocyanins, hydroxycinnamic acids, and flavones (650.67, 263.33, and 449.85 mg kg−1, respectively) compared to the other varieties. In conclusion, “Tarocco Meli” had the most interesting values for morphological parameters, “Tarocco Rosso”, “Sanguinelli”, and “Tarocco Gallo” for primary metabolites, and “Moro” for secondary metabolites. With the increasing interest in utilizing co-products, these findings could be useful in developing functional food products that meet consumer demands for healthier and more sustainable food choices.
Full article
(This article belongs to the Topic Recent Progress in Plant Nutrition Research and Plant Physiology)
►▼
Show Figures
Figure 1
Open AccessTechnical Note
Cotton Gin Stand Machine-Vision Inspection and Removal System for Plastic Contamination: Auto-Calibration Design
AgriEngineering 2023, 5(3), 1243-1258; https://doi.org/10.3390/agriengineering5030079 - 14 Jul 2023
Abstract
►▼
Show Figures
Plastic contamination in marketable cotton bales, predominantly from plastic wraps used in John Deere round module harvesters, poses a significant challenge to the U.S. cotton industry. Despite rigorous manual efforts, the intrusion of plastic into the cotton gin’s processing system persists. We have
[...] Read more.
Plastic contamination in marketable cotton bales, predominantly from plastic wraps used in John Deere round module harvesters, poses a significant challenge to the U.S. cotton industry. Despite rigorous manual efforts, the intrusion of plastic into the cotton gin’s processing system persists. We have developed a machine-vision detection and removal system aimed at mitigating this problem. This system employs inexpensive color cameras to detect plastic on the gin-stand feeder apron and subsequently removes it, reducing contamination. This system, built around low-cost ARM computers running Linux, comprises 30–50 machines and requires considerable effort to calibrate and tune. Moreover, its operation represents a technological challenge to typical cotton gin workers. This research presents a solution to this calibration operational hurdle by introducing an auto-calibration algorithm that has potential to simplify the system into a plug-and-play device. The auto-calibration system is designed to dynamically track the cotton color and utilizes frequency statistics to avoid plastic images that could compromise the system’s performance if incorporated into the auto-calibration process. We detail the design of the auto-calibration algorithm, which is expected to significantly reduce the setup overhead and facilitate the system’s continuous use. This innovation minimizes the need for skilled personnel and, therefore, is expected to expedite the system’s adoption across the cotton ginning industry.
Full article
Figure 1
Open AccessArticle
Opportunities of Digital Transformation in Post-Harvest Activities: A Single Case Study of an Engineering Solutions Provider
AgriEngineering 2023, 5(3), 1226-1242; https://doi.org/10.3390/agriengineering5030078 - 12 Jul 2023
Abstract
The purpose of this article is to identify opportunities that digital transformation in post-harvest activities offers to an engineering solution provider. The research method is a simple case study. The object is a company based in southern Brazil that provides engineering-integrated digital solutions
[...] Read more.
The purpose of this article is to identify opportunities that digital transformation in post-harvest activities offers to an engineering solution provider. The research method is a simple case study. The object is a company based in southern Brazil that provides engineering-integrated digital solutions to grain producers, including products and services. The specific objectives are to describe the company’s digital products and services, identify opportunities and players, and discuss how players can take advantage of opportunities owing to business process digitalization. The main results include separating products into three technological layers and identifying five types of opportunities (financing, commercialization, operation, logistics, traceability, and insurance), eight types of players, and the main opportunities for each player. The most significant opportunities are risk reduction in insurance contracts, improvement in grain quality, increments in food safety, and accurate information on grain movements. The main implication of the study is that grain producers and other players can explore opportunities, and solution providers can evolve toward complete digitalization by integrating service into the current offerings of post-harvest engineering solutions.
Full article
(This article belongs to the Topic Emerging Agricultural Engineering Sciences, Technologies, and Applications)
►▼
Show Figures
Figure 1
Open AccessTechnical Note
The Ear Unwrapper: A Maize Ear Image Acquisition Pipeline for Disease Severity Phenotyping
AgriEngineering 2023, 5(3), 1216-1225; https://doi.org/10.3390/agriengineering5030077 - 04 Jul 2023
Abstract
Fusarium ear rot (FER) is a common disease in maize caused by the pathogen Fusarium verticillioides. Because of the quantitative nature of the disease, scoring disease severity is difficult and nuanced, relying on various ways to quantify the damage caused by the
[...] Read more.
Fusarium ear rot (FER) is a common disease in maize caused by the pathogen Fusarium verticillioides. Because of the quantitative nature of the disease, scoring disease severity is difficult and nuanced, relying on various ways to quantify the damage caused by the pathogen. Towards the goal of designing a system with greater objectivity, reproducibility, and accuracy than subjective scores or estimations of the infected area, a system of semi-automated image acquisition and subsequent image analysis was designed. The tool created for image acquisition, “The Ear Unwrapper”, successfully obtained images of the full exterior of maize ears. A set of images produced from The Ear Unwrapper was then used as an example of how machine learning could be used to estimate disease severity from unannotated images. A high correlation (0.74) was found between the methods estimating the area of disease, but low correlations (0.47 and 0.28) were found between the number of infected kernels and the area of disease, indicating how different methods can result in contrasting severity scores. This study provides an example of how a simplified image acquisition tool can be built and incorporated into a machine learning pipeline to measure phenotypes of interest. We also present how the use of machine learning in image analysis can be adapted from open-source software to estimate complex phenotypes such as Fusarium ear rot.
Full article
(This article belongs to the Section Sensors Technology and Precision Agriculture)
►▼
Show Figures
Figure 1
Open AccessArticle
Characterizing and Predicting the Quality of Milled Rice Grains Using Machine Learning Models
by
, , , , , , , , , , , , and
AgriEngineering 2023, 5(3), 1196-1215; https://doi.org/10.3390/agriengineering5030076 - 04 Jul 2023
Abstract
Physical classification is the procedure adopted by the rice unloading, delivery, storage, and processing units for the commercial characterization of the quality of the grains. This step occurs mostly by the conventional method, which demands more time and specialized labor, and the results
[...] Read more.
Physical classification is the procedure adopted by the rice unloading, delivery, storage, and processing units for the commercial characterization of the quality of the grains. This step occurs mostly by the conventional method, which demands more time and specialized labor, and the results are subjective since the evaluation is visual. In order to make the operation faster, more accurate, and less dependent, non-destructive technologies and computational intelligence can be applied to characterize grain quality. Therefore, this study aimed to characterize and predict the quality of whole, processed rice grains, as well as classify any defects present. This was achieved by sampling from the upper and lower points of four silo dryers with capacities of up to 40,000 sacks. The grain samples had moisture contents of 16%, 17%, 18%, and 19% and were subjected to drying-aeration until reaching 12% moisture content (w.b.). Near-infrared spectroscopy technology and Machine Learning algorithm models (Artificial Neural Networks, decision tree algorithms Quinlan’s algorithm, Random Tree, REPTree, and Random Forest) were employed for this purpose. By analyzing Pearson’s correlation statistics, a strong negative correlation (R2 = 0.98) was found between moisture content and the yield of whole grains. Conversely, a strong positive correlation (R2 = 0.97) was observed between moisture content and classified physical defects across the various characterized physicochemical constituents. These findings indicate the effectiveness of near-infrared spectroscopy technology. The Random Tree model (RandT) successfully predicted the grain quality outcomes and is therefore recommended as the model of choice, obtained Pearson’s correlation coefficient (r = 0.96), mean absolute error (MAE = 0.017), and coefficient of determination (R2 = 0.92). The results obtained here reveal that the combination of near-infrared spectroscopy technology and Machine Learning algorithm models is an excellent non-destructive alternative to manual physical classification for characterizing the physicochemical quality of whole and defective rice grains.
Full article
(This article belongs to the Special Issue Food Drying and Storage Technologies)
►▼
Show Figures
Figure 1
Open AccessArticle
Effects of Bicarbonate Addition and N:P Ratio on Microalgae Growth and Resource Recovery from Domestic Wastewater
by
, , , , and
AgriEngineering 2023, 5(3), 1178-1195; https://doi.org/10.3390/agriengineering5030075 - 04 Jul 2023
Abstract
►▼
Show Figures
Nutrient availability plays a crucial role in microalgae growth in domestic wastewater. In this study, we investigated the impact of different nitrogen and phosphorus ratios (5:1, 10:1, and 20:1, m∙m−1), and the addition of inorganic carbon on microalgae growth and nutrient
[...] Read more.
Nutrient availability plays a crucial role in microalgae growth in domestic wastewater. In this study, we investigated the impact of different nitrogen and phosphorus ratios (5:1, 10:1, and 20:1, m∙m−1), and the addition of inorganic carbon on microalgae growth and nutrient uptake from domestic wastewater. Microalgae biomass achieved values ranging from 0.54 to 1.41 g·L−1. The cultivation process had maximum removal efficiencies of 83.7% for soluble chemical oxygen demand (sCOD), 74.0% for total Kjeldahl nitrogen (TKN), and 100.0% for ammonia (NH3) and orthophosphate (PO43−). All the NH3 and PO43− concentrations from domestic wastewater without supplementation were completely removed on the fourth day of cultivation. Moreover, no significant differences in microalgae growth, and NH3 and PO43− removals were observed between the conditions with and without nutrient supplementation on the fourth day of cultivation. This study has shown the feasibility of growing microalgae in domestic wastewater without any nutritional supplementation. Further investigations are required to check the long-term performance, energy requirements, and economic viability of this system for wastewater treatment and the production of nutrient-rich biomass for agricultural applications.
Full article
Figure 1
Open AccessArticle
Soil Attributes Mapping with Online Near-Infrared Spectroscopy Requires Spatio-Temporal Local Calibrations
AgriEngineering 2023, 5(3), 1163-1177; https://doi.org/10.3390/agriengineering5030074 - 03 Jul 2023
Abstract
►▼
Show Figures
Building machine learning (ML) calibrations using near-infrared (NIR) soil spectroscopy direct in agricultural areas (online NIR), soil attributes can be fine-scale mapped in a faster and more cost-effective manner, guiding management decisions to ensure the maintenance of soil functions. However, a financially and
[...] Read more.
Building machine learning (ML) calibrations using near-infrared (NIR) soil spectroscopy direct in agricultural areas (online NIR), soil attributes can be fine-scale mapped in a faster and more cost-effective manner, guiding management decisions to ensure the maintenance of soil functions. However, a financially and environmentally unattractive density of 3–5 laboratory soil samples per ha is required to build these calibrations. Since no reports have evaluated if they are reusable or if a new calibration is required for each acquisition, this study’s objective was to acquire online NIR spectra in an agricultural field where ML models were previously built and validated, assessing their performance over time. Two spectral acquisitions were held over a fallow tropical field, separated by 21 days. Soil properties (clay, organic matter, cation exchange capacity, pH, phosphorus, potassium, calcium, and magnesium) were predicted using principal components regression models calibrated with day 1 spectra. Day 1 and day 21 predicted values and maps interpolated by ordinary kriging were compared. Spectra characteristics (morphology, features, and intensity) were evaluated. Predicted values from the two days were not correlated, as no causal relationship was found for the only Pearson’s correlation coefficient (r) significative at 99% (p < 0.01) (calcium, with r = 0.22 in the comparison pairing the nearest neighbors from the two days). For clay, organic matter, and cation exchange capacity, despite their robust prediction on day 1, no significative r values were found, ranging from −0.14 to 0.32, when comparing day 1 with day 21. The maps of the two days presented no similar spatial distribution, hindering their use for management decisions. Soil moisture is a suggested source of variation, but the analysis indicated that it was not the only one, requiring further investigation of the effect of soil surface conditions and environmental variables. Although further investigations should be performed, the results presented suggest that online NIR spectra ML models require spatio-temporal local calibrations to perform properly.
Full article
Figure 1
Open AccessArticle
Spatiotemporal Dynamics of Land Use and Land Cover through Physical–Hydraulic Indices: Insights in the São Francisco River Transboundary Region, Brazilian Semiarid Area
by
, , , , , , and
AgriEngineering 2023, 5(3), 1147-1162; https://doi.org/10.3390/agriengineering5030073 - 03 Jul 2023
Abstract
This article presents a study on the spatiotemporal dynamics of land cover and use, vegetation indices, and water content in the semiarid region of Pernambuco, Brazil. This study is based on an analysis of satellite images from the years 2016, 2018, and 2019
[...] Read more.
This article presents a study on the spatiotemporal dynamics of land cover and use, vegetation indices, and water content in the semiarid region of Pernambuco, Brazil. This study is based on an analysis of satellite images from the years 2016, 2018, and 2019 using the MapBiomas platform. The results show changes in the predominant land cover classes over time, with an increase in the caatinga area and a decrease in the pasture area. An analysis of the vegetation indices (NDVI and LAI) indicated low vegetation cover and biomass in the study area, with a slight increase in the NDVI in 2018. An analysis of the Modified Normalized Difference Water Index (MNDWI) showed that the water content in the study area was generally low, with no significant variations over time. An increase in the water bodies, mainly due to the construction of a reservoir, was noted. The results of this study have provided important information for natural resource management in the region, including the development of strategies for the sustainable use and management of natural resources, particularly water resources, vegetation cover, and soil conservation.
Full article
(This article belongs to the Special Issue Application of Geographic Information System and Remote Sensing Technology in Agricultural and Forestry Research)
►▼
Show Figures
Figure 1
Open AccessArticle
Visualization of Lidar-Based 3D Droplet Distribution Detection for Air-Assisted Spraying
AgriEngineering 2023, 5(3), 1136-1146; https://doi.org/10.3390/agriengineering5030072 - 03 Jul 2023
Abstract
Air-assisted spraying is a commonly used spraying method for orchard plant protection operations. However, its spraying parameters have complex effects on droplet distribution. The lack of large-scale 3D droplet density distribution measurement methods of equipment has limited the optimization of spraying parameters. Therefore,
[...] Read more.
Air-assisted spraying is a commonly used spraying method for orchard plant protection operations. However, its spraying parameters have complex effects on droplet distribution. The lack of large-scale 3D droplet density distribution measurement methods of equipment has limited the optimization of spraying parameters. Therefore, there is a need to develop a method that can quickly obtain 3D droplet distribution. In this study, a 2D LiDAR was used to quickly scan moving droplets in the air, and a test method that can obtain the visualization of 3D droplet distribution was constructed by using the traveling mode of the machine perpendicular to the scanning plane. The 3D droplet distribution at different positions of the nozzle installed in the air-assisted system was tested at different fan rotation speeds, and the methods for signal processing, point cloud noise reduction, and point cloud division for 2D LiDAR were developed. The results showed that the LiDAR-based method for detecting 3D droplet distribution is feasible, fast, and environmentally friendly.
Full article
(This article belongs to the Special Issue Innovations in Agricultural Engineering and Mechanization for Sustainable Agriculture, Forestry and Food Production)
►▼
Show Figures
Figure 1
Open AccessArticle
Mechanical Properties of Solid Biomass as Affected by Moisture Content
AgriEngineering 2023, 5(3), 1118-1135; https://doi.org/10.3390/agriengineering5030071 - 03 Jul 2023
Abstract
The objective of the study was to examine the influence of moisture content on the mechanical properties of solid biomass, which is important for storage and handling. Mechanical properties involving powder flowability were determined with a Jenike shear tester. The materials tested were
[...] Read more.
The objective of the study was to examine the influence of moisture content on the mechanical properties of solid biomass, which is important for storage and handling. Mechanical properties involving powder flowability were determined with a Jenike shear tester. The materials tested were powdered biomass: sunflower husks, apple pomace, dried distillers grains with solubles (DDGS), and meat and bone meal. In static operations in which powdered biomass is generally under a significant load, such as in silos, moisture deteriorates the mechanical properties of biomass and increases its cohesion. In the case of DDGS, an additional slight decrease in stress was observed for samples with the highest moisture content, which was above 20%. For meat and bone meal and sunflower husks, a lubrication phenomenon was clearly observed, in which biomass samples with increased moisture content manifested better flowability, requiring lower boundary shear stresses than less moist samples. For apple pomace samples, with normal stresses above 50 kPa, the addition of moisture above 10% did not change the values of the observed shear stresses, indicating the stability of their properties. The use of powdered biomass with higher moisture contents, at above 10%, should be avoided, as such material can lead to overhangs in tanks and silos.
Full article
(This article belongs to the Special Issue Postharvest Storage Technologies)
►▼
Show Figures
Figure 1
Open AccessArticle
Assessing the Effects of Free Fall Conditions on Damage to Corn Seeds: A Comprehensive Examination of Contributing Factors
AgriEngineering 2023, 5(2), 1104-1117; https://doi.org/10.3390/agriengineering5020070 - 20 Jun 2023
Abstract
Corn is a staple food crop grown in over 100 countries worldwide. To meet the growing demand for corn, losses in its quality and quantity should be minimized. One of the potential threats to the quality and viability of corn is mechanical damage
[...] Read more.
Corn is a staple food crop grown in over 100 countries worldwide. To meet the growing demand for corn, losses in its quality and quantity should be minimized. One of the potential threats to the quality and viability of corn is mechanical damage during harvesting and handling. Despite extensive research on corn, there is a lack of reliable data on the damage its seeds undergo when they are subjected to mechanical impact against different surfaces during handling and transportation. This study is designed to investigate the effects of (a) drop height (5, 10, and 15 m) during free fall, (b) impact surface (concrete, metal, and seed to seed), seed moisture content (10, 15, 20, and 25% w.b), and ambient temperature (−10 and 20 °C) on the percentage of physical damage (PPD) and physiological damage to corn seeds. The PPD and the extent of physiological damage were determined as the percentage of seed breakage and the percentage of loss in germination (PLG), respectively. The latter parameter was specifically chosen to evaluate seeds that showed no visible external damage, thus enabling the assessment of purely internal damage that PPD did not capture. This approach enabled a comprehensive analysis of free fall’s influence on the seeds’ quality and viability, providing a complete picture of the overall impact. Total damage was then calculated as the sum of PPD and PLG. An evaluation and modeling process was undertaken to assess how corn seed damage depends on variables such as drop height, moisture content, impact surfaces, and temperatures. The results revealed that seeds dropped onto metal surfaces incurred a higher total damage (15.52%) compared to concrete (12.86%) and seed-to-seed abrasion (6.29%). Greater total damage to seeds was observed at an ambient temperature of −10 °C (13.66%) than at 20 °C (9.46%). Increased drop height increased seeds’ mass flow velocity and correspondingly caused increases in both physical and physiological damage to seeds. On the other hand, increased moisture levels caused a decreasing trend in the physical damage but increased physiological damage to the seeds. The limitations of the developed models were thoroughly discussed, providing important insights for future studies. The results of this study promise to deliver substantial benefits to the seed/grain handling industry, especially in minimizing impact-induced damage.
Full article
(This article belongs to the Section Pre and Post-Harvest Engineering in Agriculture)
►▼
Show Figures
Figure 1
Open AccessArticle
Evaluation of Body Surface Temperature in Pigs Using Geostatistics
by
, , , , , , , , and
AgriEngineering 2023, 5(2), 1090-1103; https://doi.org/10.3390/agriengineering5020069 - 19 Jun 2023
Abstract
This paper explores the potential of infrared thermography and geostatistics in animal production and presents the results of the application of the combination of these techniques, contributing significantly to efforts to obtain animals’ responses to the environments in which they are located and
[...] Read more.
This paper explores the potential of infrared thermography and geostatistics in animal production and presents the results of the application of the combination of these techniques, contributing significantly to efforts to obtain animals’ responses to the environments in which they are located and thereby ensuring improvements in productivity and animal welfare. The objective was to verify the variability in surface temperature in pigs submitted to different climate control systems using geostatistics. Three growing animals per stall were selected. Dry bulb temperature (Tbd, °C), relative humidity (RH, %) and thermal images were recorded at 08:00 and 12:00 h. To analyze the data, semivariograms were made, the theoretical model was validated and kriging maps were constructed. The mean temperature of the pigs in the pen with adiabatic evaporative cooling (AEC) ranged from 32.40 to 36.25 °C; for the pigs in the forced ventilation (FV) pen, the range of variation was from 32.51 to 36.81 °C. In the control group (Con), with natural ventilation, the average temperature was 37.51 to 38.45 °C. The geostatistical analysis provided a mathematical model capable of illustrating the variation in temperature in the caudal–dorsal regions of the pigs according to the environments to which the animals were subjected.
Full article
(This article belongs to the Topic Emerging Agricultural Engineering Sciences, Technologies, and Applications)
►▼
Show Figures
Figure 1
Open AccessTechnical Note
Nuclear Laboratory Setup for Measuring the Soil Water Content in Engineering Physics Teaching Laboratories
by
and
AgriEngineering 2023, 5(2), 1079-1089; https://doi.org/10.3390/agriengineering5020068 - 15 Jun 2023
Abstract
►▼
Show Figures
Soil water content (θ) is a crucial soil parameter that is determined in many studies involving engineering, geology, and soil and environmental sciences. For instance, evaluating the soil strength, groundwater recharge, hydraulic conductivity, and soil aeration status depends on θ. The measurement of
[...] Read more.
Soil water content (θ) is a crucial soil parameter that is determined in many studies involving engineering, geology, and soil and environmental sciences. For instance, evaluating the soil strength, groundwater recharge, hydraulic conductivity, and soil aeration status depends on θ. The measurement of θ is fundamental for monitoring and controlling several soil processes. The gamma-ray attenuation (GRA) technique is a fast and non-destructive way of evaluating θ in soils with very contrasting compositions. Although, GRA is rarely explored in lab physics classes. The proposal of an experiment using a teaching GRA apparatus for measuring θ is presented. The experimental setup consisted of a 137Cs radioactive source, a Geiger-Müller detector, and a radiation counter. Soil samples with four distinct granulometric compositions were analyzed. Strong linear correlations were found between the transmitted gamma-ray photon intensity and θ (correlation coefficients varying from −0.95 to −0.98). The soil porosity, measured by the conventional and GRA methods, presented differences that varied from c. 7.8% to c. 18.2%. In addition, strong linear relationships (correlation coefficients from 0.90 to 0.98) were observed between the GRA and the traditional (gravimetric) method of θ measurement. It was verified that the teaching GRA apparatus is useful for measuring θ. In addition, the apparatus allows the introduction of some important aspects related to the study of modern physics for undergraduate students of many fields of knowledge.
Full article
Figure 1
Open AccessArticle
Occurrence of Multiple Glyphosate-Resistant Weeds in Brazilian Citrus Orchards
by
, , , , , and
AgriEngineering 2023, 5(2), 1068-1078; https://doi.org/10.3390/agriengineering5020067 - 14 Jun 2023
Abstract
►▼
Show Figures
Glyphosate is the most widely used herbicide for weed control in citrus orchards in Brazil; therefore, it is likely that several species have gained resistance to this herbicide and that more than one resistant species can be found in the same orchard. The
[...] Read more.
Glyphosate is the most widely used herbicide for weed control in citrus orchards in Brazil; therefore, it is likely that several species have gained resistance to this herbicide and that more than one resistant species can be found in the same orchard. The objective was to identify weeds resistant to glyphosate in citrus orchards from different regions of the São Paulo State (SP) and determine how many resistant species are present within the same orchard. Seeds of Amaranthus deflexus, A. hybridus, Bidens pilosa, Chloris elata, Conyza bonariensis, Digitaria insularis, Solanum Americanum, and Tridax procumbens, which, as reported by growers, are suspected to be resistant to glyphosate, were collected from plants that survived the last application of this herbicide (>720 g of acid equivalent [ae] ha–1) in sweet orange and Tahiti acid lime orchards. Based on dose–response and shikimic acid accumulation assays, all populations of A. deflexus, A. hybridus, B. pilosa, and T. procumbens were sensitive to glyphosate. However, populations of B. pilosa from the Olimpia region (R-NS, R-PT and R-OdA) showed signs of resistance based on plant mortality rates by 50% within a population (LD50 = 355–460 g ae ha−1). All populations of C. bonariensis, C. elata, and D. insularis were resistant to glyphosate, presenting resistance ratios from 1.9 to 27.6 and low shikimate accumulation rates. Solanum americanum also showed resistance, with resistance ratios ranging from 4.3 to 25.4. Most of the citrus orchards sampled presented the occurrence of more than one species resistant to glyphosate: Nossa Senhora—one species; Olhos D’agua and Passatempo—two species; Araras—four species; and Cordeiropolis and Mogi-Mirim—up to five species. The results reported in this paper provide evidence of multiple species in citrus orchards from São Paulo that have exhibited resistance to glyphosate. This underscores the difficulties in managing glyphosate-resistant weeds which are prevalent throughout the country, such as C. bonariensis and D. insularis. The presence of these resistant species further complicates the control of susceptible species that may also develop resistance. In addition, the glyphosate resistance of S. americanum was identified for the first time.
Full article
Figure 1
Open AccessArticle
Using Continuous Output Neural Nets to Estimate Pasture Biomass from Digital Photographs in Grazing Lands
AgriEngineering 2023, 5(2), 1051-1067; https://doi.org/10.3390/agriengineering5020066 - 09 Jun 2023
Abstract
►▼
Show Figures
Accurate estimates of pasture biomass in grazing lands are currently a time-consuming and resource-intensive task. The process generally includes physically cutting, bagging, labelling, drying, and weighing grass samples using multiple “quadrats” placed on the ground. Quadrats vary in size but are typically in
[...] Read more.
Accurate estimates of pasture biomass in grazing lands are currently a time-consuming and resource-intensive task. The process generally includes physically cutting, bagging, labelling, drying, and weighing grass samples using multiple “quadrats” placed on the ground. Quadrats vary in size but are typically in the order of 0.25 m2 (i.e., 0.5 m × 0.5 m) up to 1.0 m2. Measurements from a number of harvested quadrats are then averaged to get a site estimate. This study investigated the use of photographs and ‘machine learning’ to reduce the time factor and difficulty in taking pasture biomass measurements to potentially make the estimations more accessible through the use of mobile phone cameras. A dataset was created from a pre-existing archive of quadrat photos and corresponding hand-cut pasture biomass measurements taken from a diverse range of field monitoring sites. Sites were clustered and one was held back per model for testing. The models were based on DenseNet121. Individual quadrat errors were large but more promising results were achieved when estimating the site mean pasture biomass. Another two smaller additional datasets were created post-training which were used to further assess the ensemble; they provided similar absolute errors to the original dataset, but significantly larger relative errors. The first was made from harvested quadrats, and the second was made using a pasture height meter in conjunction with a mobile phone camera. The models performed well across a variety of situations and locations but underperformed when assessed on some sites with very different vegetation. More data and refinement of the approach outlined in the paper will reduce the number of models needed and help to correct errors. These models provide a promising start, but further investigation, refinement, and data are needed before becoming a usable application.
Full article
Figure 1
Highly Accessed Articles
Latest Books
E-Mail Alert
News
Topics
Topic in
Agriculture, AgriEngineering, Energies, Sustainability, Water
Emerging Agricultural Engineering Sciences, Technologies, and Applications
Topic Editors: Muhammad Sultan, Yuguang Zhou, Redmond R. Shamshiri, Muhammad ImranDeadline: 31 August 2023
Topic in
AgriEngineering, Antioxidants, Horticulturae, Nanomaterials, Plants
Recent Progress in Plant Nutrition Research and Plant Physiology
Topic Editors: Renato De Mello Prado, Cid Naudi Silva CamposDeadline: 31 December 2023
Topic in
Agriculture, AgriEngineering, Agronomy
Current Research on Intelligent Equipment for Agriculture
Topic Editors: Changyuan Zhai, Ning Wang, Jianfeng ZhouDeadline: 30 June 2024
Conferences
Special Issues
Special Issue in
AgriEngineering
Postharvest Storage Technologies
Guest Editors: Evandro De Castro Melo, Renata Cassia CamposDeadline: 25 August 2023
Special Issue in
AgriEngineering
Sensors and Actuators for Crops and Livestock Farming
Guest Editors: Santosh Pandey, Tiago PaimDeadline: 1 October 2023
Special Issue in
AgriEngineering
Remote Sensing-Based Machine Learning Applications in Agriculture
Guest Editor: Murali Krishna GummaDeadline: 1 November 2023
Special Issue in
AgriEngineering
Big Data Analytics in Agriculture
Guest Editors: Stanley Robson De Medeiros Oliveira, Kleber Xavier Sampaio De Souza, Sônia TernesDeadline: 30 November 2023